EMC/EMI Test & Measurement Equipment - The EMC Shop

EMC Test Equipment Categories

Transient Generators

EMI Receivers/EMC Analyzers

RF Power Amplifiers

Electric Field Strength Measurement

RF Conducted Immunity Test Systems

EMC Antennas

Line Impedance Stabilization Networks (LISN's)

EMC Probes

EM Coupling Clamps

Coupling Decoupling Networks (CDN's)

RF Current Probes/Monitors

EMC/EMI Signal Generators

Calibration Equipment

Software for EMC Testing

EMC Test Equipment Test Equipment, Systems & Solutions

Teseq MD 102A ESD Pulse Measurement Target for IEC/EN 61000-4-2

SKU: sku-887

Inquire for Lead Time

VIEW PRODUCT Cart
Com-Power LI-220C 9 kHz - 30 MHz LISN for CISPR 16-1-2/ANSI C63.4

SKU: 10878

Weight: 20.5 lbs / 9.3 kg

Application/Test Type: Power line conducted emissions tests

Current Rating: 20 Amperes AC, 14 Amperes DC

Dimensions: 16.75 x 15.5 x 7.5 inches / 42.5 x 39.3 x 19 cm

Frequency Range: 9 KHz - 30 MHz

Inductors: 250 & 50 microhenry (air-core)

Insertion Loss: 6 dB to 1 dB

Isolation: 20 dB to 40 dB

Mains & EUT Connections: Superior Electric SUPERCON® shrouded sockets

RF Connector: 50Ω N-type (female)

Standards Met: CISPR 16-1-2 / ANSI C63.4

Voltage Rating: 270 VAC (Line to Ground), 380 VDC

Cost New:

Was:

Price Now:

$295.00 - $3,965.00

Typically In Stock

ORDERING OPTIONS
Solar 7054-2 EMI Voltage Spike Generator

SKU: 30184

Test Standards: DO-160 SECTION 17, MIL-STD-462

Applications: EMI/EMC For Military Aircraft And Aviation

Spike Amplitude: 10 - 400 Volts

Spike Repetition Rate: 0.8 - 10 Pulses Per Second

Spike Rise Time: 10 microseconds

Cost New:

Was:

Price Now:

$1,750.00 - $1,950.00

IN STOCK

ORDERING OPTIONS
Fischer Custom Communications F-2031-A-DCN-23mm Decoupling Ferrite Tube for IEC 61000-4-6

SKU: sku-727

Weight: 7.5kG

Application/Test Type: ferrite decoupling clamp

Dimensions: Aperture: 23mm Length: 610mm Height: 134mm

Frequency Range: 100kHz - 100MHz

Standards Met: IEC/EN 61000-4-6

VIEW PRODUCT Cart
EM Test Automotive Test System for ISO 7637-2

SKU: 10596

ISO Automotive Standards: ISO 7637-2, ISO 16750-2, ISO 11452-8

SAE Automotive Standards: SAE J1113, SAE J1455

Freestyle Mode Micropulses: Programmable Rise time 1us - 10us in steps of 1us; Pulse duration 50us - 10,000us; Int. resistor 2ohm - 100ohm in steps of 5ohm; 200ohm, 400ohm and 450ohm

Input: DUT supply +/- DC voltage from VDS 200N or any other DC supply; Pulse 5, 7 From one LD 200N

Micropulse: Micropulse module for test pulses 1, 2A and 6

Trigger: automatic, manual, external, battery switch

UCS 200N Models: Built-in coupling/decoupling networks: UCS 200N50, 80V/50A, 100A@500ms; UCS 200N100, 80V/100A, 150A@500ms; UCS 200N150, 80V/150A UCS 200N200 80V/200A

Verification: As per Annex C of ISO 7637-2:2011 into 50ohm and 1,000ohm load

Applications: EMC Testing on EV Electric Vehicles Batteries & Charging Stations, Automotive Electrical Disturbances

Inquire for availability

VIEW PRODUCT Cart
Keytek E503 Ring Wave Simulator for ANSI/IEEE C62.4 and UL 864

SKU: 10546

Pulse current (short circuit): Selectable at 200A max. or 500A max., when the open-circuit voltage is set to 6.0kV.

Pulse repetition: 1 shot/9 seconds

Pulse voltage (open circuit): 200V - 6.6kV ± 10%

Ringwave 0.5 μs/100 kHz: Pulse conforms to IEC/EN 61000-4-12 and ANSI (IEEE) C62.41

Standards Met: ANSI/IEEE C62.41 Cat. A and B, and various UL standards, including UL 864

Equipment Group: Ring Wave Generators/Simulators

IN STOCK

VIEW PRODUCT Cart
Schaffner CDN 8014 Burst/EFT Coupling Clamp for EN/IEC 61000-4-4

SKU: 10545

Compatible Generators: EFT Generators Electrical Noise/Transient Immunity

Standards Met: IEC/EN 61000-4-4

Cost New:

Was:

Price Now:

$2,990.00

Inquire for Availability
Noiseken ESS-S3011A & GT-30RA Electrostatic Discharge Simulator System for up to 30kV Testing

SKU: 8250

Weight: Approx. 7.0kg (gun holder excluded) Approx. 7.5kg (gun holder included)

Air Discharge Voltage Range: 0.20kV to 30.0kV±5%（30.5kVmax）10.0kV : 0.01kV step 30.0kV : 0.1kV step

Standards Met: IEC 61000-4-2, ISO 10605

Battery: AC100V to AC240V 50Hz／60Hz ±10% 75VA

Contact Discharge Voltage Range: 0.20kV to 30.0kV±5% （30.5kVmax） 10.0kV : 0.01kV step 30.0kV : 0.1kV step

Polarity: positive/negative

Pre-Programmed IEC Levels: Yes

Resolution: 10 Volt steps up to 10 kV; 100 Volt steps to 30 kV

Typically In Stock

VIEW PRODUCT Cart
Em Test CWS 500N1.4 RF Conducted Immunity Test System for IEC 61000-4-6

SKU: 11251

Test Capabilities: RF Conducted Immunity

Standards Met: IEC/EN 61000-4-6

Applications: Radiated Immunity Debugging, CE Marking, Medical Devices, Industrial Machinery, Electronics & IT

CDN Test Levels (w/ built-in amplifier): 40Vrms

BCI Test Levels (w/ built-in amplifier): 8Vrms

Frequency Range (w/ built-in amplifier): 150 kHz - 230 MHz

Typically In Stock

VIEW PRODUCT Cart
PMM 3010 EMC RF Signal Generator, 9 kHz to 1 GHz

SKU: 30169

Frequency Range: 9 kHz to 1 GHz

Frequency Resolution: 1 kHz

Frequency Accuracy: ± 10 ppm @ f > 10 MHz

Level Range: -107 to +10 dBm

Output Impedance: 50 Ω

Connector: N-Type (f)

Applications: Radiated Immunity

Test Standards: IEC 61000-4-3

Typically in Stock

VIEW PRODUCT Cart
Com-Power FCLCE-1000 Current Probe Calibration Fixture

SKU: 11601

Output resistance: 50 Ohms

RF Connector: N-Type

VIEW PRODUCT Cart
EMIC-20 EM Injection Clamp for IEC/EN 61000-4-6 Immunity Test

SKU: 7851

Standards: EN/IEC 61000-4-6

Application/Test Type: Injects the disturbance signal through a combination of inductive and capacitive coupling

Clamp factor (CF): -.5 dB at 100 kHz to -4 dB at 1 GHz (Min -7 dB at 700 MHz

Connector: N-type female

Dimensions: 632 mm x 120 mm x 80 mm

Frequency Range: 10 kHz to 1000 MHz

Max. Cable Diameter: 20 mm

Maximum Continuous Power: 0.15 to 100 MHz: 100 W for 15 min; 100 to 230 MHz: 100 W for 5 min; 230 to 1000 MHz: 50 W for 3 min

Test Setup and Overview: RF Conducted Immunity Testing

Cost New:

Was:

Price Now:

$595.00 - $8,500.00

Typically In Stock

ORDERING OPTIONS