EM Coupling Clamps

(Showing 12 of 15)

The integrity of both communication and electrical lines within products of all shapes and sizes is important to address early in design stages. EM coupling clamps are used to monitor electrical and magnetic characteristics radiated from electrical/communication wires. Additionally, you can generate electrical and magnetic fields using a clamp to inject distrubances onto the lines and evaluate their response. EM clamps are used to meet CISPR, IEC and other compliance standards to evaluate radio frequency disturbances on and around power or data lines.

The EMC Shop is an ISO 17025 accredited company and a preferred North American vendor with the widest selection of EM coupling clamps in stock. Get Application Support, Pricing, Lead Time and More: Contact Form

RESA Realtime EMC Spectrum Analyzer

Rent Keysight N9048B CISPR 16 EMI Receiver

Teseq NSG 3040-IEC Test System for Surge Combination Wave, EFT/Burst, Dips Interrupts & Variations w/ 16 A CDN

PMM 9030 3 GHz Extension Unit for 9010

EM Clamp Test Setup per IEC 61000-4-6

EM Coupling Injection Clamp Test Setup per IEC 61000-4-6

EM Injection Clamp Video Overview

Show 12

EM Coupling Clamps Test Equipment, Systems & Solutions

  • EMIC-35 Current Injection Clamp for RF Conducted Immunity Testing
    Quick view

    EMIC-35 Current Injection Clamp for RF Conducted Immunity Testing

    SKU: sku-2132

    Weight: approx. 14 kg
    Application/Test Type: Injects the disturbance signal through a combination of inductive and capacitive coupling
    Clamp factor (CF): -.6 dB at 100 kHz to -2.2 dB at 1 GHz (Min -4 dB at 700 MHz
    Connector: N-type female
    Dimensions: 666 mm x 135 mm x 120 mm
    Frequency Range: 10 kHz to 1000 MHz
    Impedance: 50 Ohms
    Max. Cable Diameter: 35 mm
    Maximum Continuous Power: 0.15 to 100 MHz: 100 W for 15 min; 100 to 230 MHz: 100 W for 5 min; 230 to 1000 MHz: 50 W for 3 min
    Standards Met: IEC/EN 61000-4-6; CISPR 24; EN 61000-6-1; EN 61000-6-2; IEC 60533; IEC 60601-1-2; IEC 61326
    View Product Cart
  • Teseq AMZ 41A Absorbing Clamp for CISPR 13 & 14, w/ LE 210 RF Cable
    Quick view

    Teseq AMZ 41A Absorbing Clamp for CISPR 13 & 14, w/ LE 210 RF Cable

    SKU: sku-568

    Weight: approx. 7 kg
    Application/Test Type: Disturbance power measurements of coaxial cables, automotive screened components (eg motor ignition systems and sheath current on aerial cables.
    Clamp factor (CF): -4 dB to +5 dB
    Current Rating: 25 Amps Max
    Decoupling factor DF: Greater than 21 dB
    Decoupling factor DR: Greater than 30 dB
    Dimensions: W x D x H: 665 mm x 120 mm x 105 mm
    Frequency Range: 30 MHz to 1000 MHz
    Isolated lines under test: Power supply lines and other connecting lines
    Max. Cable Diameter: 20 mm inner (10 mm with adapter)
    Maximum Continuous Power: 10 Watts
    Min. site attenuation: 13 dB to 22 dB
    RF Connector: BNC, 50 Ω
    Standards Met: CISPR 13, CISPR 14-1, CISPR 16-1-5, CISPR 16-2-2
    View Product Cart
  • EMIC-20 EM Injection Clamp for IEC/EN 61000-4-6 Immunity Test
    Quick view

    EMIC-20 EM Injection Clamp for IEC/EN 61000-4-6 Immunity Test

    SKU: sku-524

    Standards: EN/IEC 61000-4-6
    Application/Test Type: Injects the disturbance signal through a combination of inductive and capacitive coupling
    Clamp factor (CF): -.5 dB at 100 kHz to -4 dB at 1 GHz (Min -7 dB at 700 MHz
    Connector: N-type female
    Dimensions: 632 mm x 120 mm x 80 mm
    Frequency Range: 10 kHz to 1000 MHz
    Max. Cable Diameter: 20 mm
    Maximum Continuous Power: 0.15 to 100 MHz: 100 W for 15 min; 100 to 230 MHz: 100 W for 5 min; 230 to 1000 MHz: 50 W for 3 min
    Typically In Stock
    View Product Cart
  • Com-Power CLA-150 32mm Absorbing Clamp
    Quick view

    Com-Power CLA-150 32mm Absorbing Clamp

    SKU: sku-266

    Weight: 21 lbs (9.5 Kg)
    Aperture: 34.9 mm (1.37 inches)
    Application/Test Type: Measurement of direct field strength from EUT supply cables
    Clamp factor (CF): -3 dB to +4 dB
    Dimensions: 627 x 114 x 165 mm (24.7 x .4.5 x 6.5 inches)
    Frequency Range: 30 MHz to 1000 MHz
    Isolated lines under test: Power supply lines and other connecting lines
    Max. Cable Diameter: 32 mm (1.26 inches)
    Min. site attenuation: 14 dB to 21 dB
    RF Connector: BNC (f), 50 Ohms
    Standards Met: CISPR 14
    View Product View Product
  • Com-Power CLA-050 10mm Absorbing Clamp
    Quick view

    Com-Power CLA-050 10mm Absorbing Clamp

    SKU: sku-265

    Weight: 5 kg (11.5 lbs)
    Aperture: 12.7 mm (0.5 inches)
    Application/Test Type: Measurement of direct field strength from EUT supply cables
    Clamp factor (CF): -3 dB to +4 dB
    Dimensions: 627 x 114 x 144 mm (24.7 x .4.5 x 5.7 inches)
    Frequency Range: 30 MHz to 1000 MHz
    Isolated lines under test: Power supply lines and other connecting lines
    Max. Cable Diameter: 10 mm (0.39 inches)
    Min. site attenuation: 14 dB to 21 dB
    RF Connector: BNC (f), 50 Ohms
    Standards Met: CISPR 14
    View Product Cart

Connect with The EMC Shop

Our experienced staff can help you with applications, purchase and rental options.

Contact Form