Schwarzbeck ISN S8 Impedance Stabilization Network per IEC/CISPR 22

Schwarzbeck ISN S8 Impedance Stabilization Network per IEC/CISPR 22

Condition:
New
Connector to EUT:
RJ45 connector | CAT 6 Cable
Max Voltage Handling:
150 VDC | 100 VAC
Max Current Handling:
1 Amp
Standards Met:
CISPR 22, CISPR 32, EN 55022
Manufacturer:
Schwarzbeck
Online Orders Ship Same Day

 

Availability:

IN STOCK

SKU:
11271

 

This product is available for shipping to North America and Western European countries.

Getting Started...

Check out our Google Reviews

Schwarzbeck ISN S8 Overview

The ISN S8 can be used to measure the conducted voltage emissions of telecommunication and data processing equipment. It is designed to measure shielded cables with up to 4 wire pairs. It is based on IEC/CISPR 22 and the related national standards. The special circuitry and design is described in CISPR 22, CISPR 32 Annex G.11 and EN 55022 Annex D figure D.11 respectively. The ISN must provide sufficient decoupling from the equipment under test (EuT) to the auxiliary equipment (AE) which could be a communication device or a kind of load. The measured conducted voltage is coupled out to the BNC connector on top of the ISN S8. An EMI receiver or spectrum analyzer is most commonly used for a measuring instrument.

The ISN S8 can also be used in the other direction to inject conducted radio frequency disturbance into the shield of communication wires. This method is described in IEC/EN 61000-4-6. If the ISN S8 is used for injection it is also referred to as coupling decoupling network (CDN).

The ISN S8 is capable to provide 1000 MBit/s (Gigabit-Ethernet, 1000BASE-T). A cable of the suitable cable category is built in and is wired according to TIA-568A/B.

Specifications
Frequency Range 150 kHz – 230 MHz
Type of cable 4 x STP (shielded twisted pair) 100 Ohm impedance
Connector RJ45
Max. voltage line – ground 150 V DC
100 V AC
Max. line current/path 1 A DC
Common mode impedance EuTside:
150 kHz – 30 MHz
30 MHz – 230 MHz		 150 Ohm ±20 Ohm
150 Ohm + 60 Ohm/-45 Ohm
Phase error 0° ±20°
Measuring port 50 Ohm BNC
Max. voltage measuring port <20 V AC
Voltage divisions factor EuT – measuring port:
150 kHz – 30 MHz
30 MHz – 230 MHz		 9.5 dB ±1 dB
9.5 dB +4 dB/-2 dB
3 dB transmission bandwith EuT – AE >250 MHz
Cable-/RJ-45 connector cat. CAT 6
Dimensions W x H x D 225 mm x 129 mm x 105 mm
Weight ~1265 g
Acc. to standard CISPR 22
CISPR 32
EN 55022

The measurement is described in detail in CISPR 22, CISPR 32 and EN 55022.

The equipment under test must be connected to the EuT-port. The auxiliary equipment has to be connected to the AEport. The EMI-receiver or spectrum analyser has to be connected to the BNC port of the ISN S8 using a coaxial line.

Fixture lugs at the bottom plate of the ISN S8 allow to fix the device with screws to the cabin wall if wished.

As CISPR 22 defines the limits for conducted emissions in a 150 Ohm system there is an 100 Ohm resistor in series to the BNC connector. In combination with the 50 Ohm input resistance of the measurement device a voltage division factor of 1:3 follows. In a logarithmic scale this is equal to 9.5 dB. The measured voltages across 50 Ohm therefore has to be multiplied with 3 or in other words a correction of 9.5 dB must be added. This value of 9.5 dB is called the voltage division factor (VDF). This VDF is slightly frequency dependent. For very precise measurements it is recommended to take the exact frequency dependent VDF into account (see calibration certificate).

The shield or outer cable is defined as the common mode point for the EuT connector of ISN/CDN equipment. To be able to do a measurement (i.e. the impedance of the ISN or to normalize the voltage division factor) at this measuring point an adapter is needed.

This adapter can be purchased separately and is needed to connect the shield of the RJ45 socket to the measurement device. It is called “CA ISN S8” where the Usection can be attached to the shield of the RJ45 socket at the EuT part of the ISN and the 4 mm plug matches into the 50 ? to 150 ? adapter SR100-6W which can be purchased separately as well. It is given that when putting the ISN S8 and the SR100-6W together the normative distance of 30 mm between the front surfaces automatically is fulfilled.

Cal Adapter for ISN S8 for EMI Measurements to CISPR 22, CISPR 32 and More To enable you to connect your own measurement equipment the CA ISN S8 consists of two parts and can be taken apart very easily. A 4 mm plug provides the connection to the SR100-6W keeping the given distance.

If you want to use the ISN S8 as a CDN the use of the adapter “CA ISN S8”and the 50 Ohm to 150 Ohm adapter “SR100-6W” is mandatory. The measurement setup is described within the norm IEC/EN 61000- 4-6 picture 8c.

RESA Realtime EMC Spectrum Analyzer

RESA Realtime EMC Spectrum Analyzer

RESA Realtime EMC Spectrum Analyzer

RESA Realtime EMC Spectrum Analyzer

Schwarzbeck ISN S8 Key Considerations

Manufacturer:
Schwarzbeck
Connector to EUT:
RJ45 connector | CAT 6 Cable
Max Voltage Handling:
150 VDC | 100 VAC
Max Current Handling:
1 Amp
Standards Met:
CISPR 22, CISPR 32, EN 55022

Related EMC Equipment & Solutions

FCC CISPR 22 Impedance Stabilization Network (ISN) FCC-TLISN-T4-02

FCC CISPR 22 Impedance Stabilization Network (ISN) FCC-TLISN-T4-02

SKU: sku-267

Weight: 1.0 kg (2.2 pounds)
Application/Test Type: Measuring conducted emissions on two balanced pair telecom ITE’s.
Common Mode Impedance: 150 ± 20Ω
Current Rating: 250 mA Maximum
Decoupling of Common Mode Disturbance: 35 dB min. to 150 kHz; 55 dB min up to 30 MHz
Dimensions: 100 x 100 x 235 mm
Frequency Range: 150 kHz to 30 MHz
Mains & EUT Connections: D-sub 25 female
RF Connector: 50Ω BNC female
Voltage Division Factor: 9.5 dB ±1 dB
Voltage Rating: 63 VAC RMS, 100 VDC
In Stock
View Product Cart
Teseq ISN T800S Impedance Stabilization Network per CISPR 22/32 Figure D.3/G.3

Teseq ISN T800S Impedance Stabilization Network per CISPR 22/32 Figure D.3/G.3

SKU: sku-861

Weight: 1.2 lbs. (0.55 kg)
Connectors: 105 x 65 x 110 mm
Current Rating: 600 mA (per line), 1.2 Amps (per pair)
Dimensions: see photo in images
Frequency Range: 150 kHz to 30 MHz
Isolation: Cat 3 - 150 kHz to 30 MHz: 39.3 to 55 dB Cat 5 - 150 kHz to 2 MHz: 65 dB Cat 5 - 2 MHz to 30 MHz:: 49.3 dB to 65 dB
Mains & EUT Connections: RJ11 and RJ45
RF Connector: 50Ω N-type (female)
Standards Met: CISPR 16-1-2, CISPR 22/32
Voltage Rating: 63 VAC 100 VDC
View Product Cart
Teseq ISN T8 Impedance Stabilization Network (ISN) for Unscreened Balanced Pairs

Teseq ISN T8 Impedance Stabilization Network (ISN) for Unscreened Balanced Pairs

SKU: 10161

Weight: 550 grams (1800 grams with storage case)
Application/Test Type: 1000BaseT and Power Over Ethernet (PoE) testing of 1 up to 4 pair(s) of unscreened balanced communication lines
Common Mode Impedance: 150 Ω ±20 Ω
Current Rating: 600 mA (line), 1200 mA (pair)
Decoupling of Common Mode Disturbance: ≥35 dB to ≥55 dB/≥55 dB
Dimensions: 10.5 cm x 6.5 cm x 11.0 cm (19.0 cm with adapter plugged in)
Frequency Range: 150 kHz to 30 MHz
Mains & EUT Connections: Adapter Set includes RJ11, RJ45, LCL and more.
RF Connector: BNC 50 Ω
RF Input Voltage: 15 V max
Standards Met: CISPR 15; CISPR 16-1-2; CISPR 16-2-1;CISPR 22; CISPR 32; EN 61000-6-3; EN 61000-6-4
Voltage Division Factor: 10 dB ±1 dB
Voltage Rating: 63 Volts AC, 100 Volts DC (line to ground); Test Voltage: 200VDC, 2 seconds
View Product View Product

Connect with The EMC Shop

Our experienced staff can help you with applications, purchase and rental options.

Contact Form