Schwarzbeck CDNE M2 Coupling Decoupling Network

CDNs have been used as coupling- /decoupling networks to measure conducted noise as well as for immunity testing so far. Contrary to the couple-/decouple networks (CDN) described in IEC/EN 61000-4-6 the category of CDNE has been created especially for the measurement of emissions of luminaries featuring tighter tolerance.

Attention! The CDNE is not appropriate for measuring immunity!

in EN 55015. The tolerances of the asymmetric impedance became tighter. The tolerance for the voltage division factor is now defined constantly over the whole frequency range and a new requirement for a defined symmetrical impedance has been introduced for the frequency range 30 MHz to 300 MHz.

For measurements on DuTs without PE one has to use the CDNE M2. For measurements using PE,N and L the CDNE M3 has to be used.

The interference voltage emitted by the device under test can be measured at the BNC jack of the measurement port. The voltage division factor to this port is 20 dB.

Due to the current-compensated coils within the CDNE it is ensured that there is a minimum decoupling of at least 30 dB between EuT and AE. Noise coming from the mains side is thus well kept away for the measurement.

The connection to ground can be accomplished using the ground plane of the CDNE. Additionally there is a M4 thread located at the AE side to ground as well as a 4 mm socket to connect the device to ground.

To improve the operational safety the mains voltage-carrying connections are carried out as security sockets. We recommend to use special 4 mm security plugs if you plan to design your own adapters. Those connectors can be purchased optionally.

To verify the CDNE some measurements require a common mode potential. The common mode reference point is defined for CDNE devices for unshielded cables as the short-circuiting point of all wires.

To be able to measure at the herein before mentioned point to check the standard values of the CDNE (i.e. common mode impedance, voltage division factor) a low-inductance and lowresistance short circuit jumper is required.

This adapter is available optionally. It consists of two parts. There is a shortcircuit bridge (CA CDNE M2 Part A) and an adapter kit (CA CDNE Part B).

CA CDNE M2 Part A

CA CDNE Part B

Warning! Under no circumstances the short-circuit jumper may be used while AE is connected to mains!

One of the most important characteristics of the CDNE is the coupling attenuation between the EuT port and the BNC measurement port (other expressions: correction or Voltage Division Factor VDF). This attenuation is recorded for each device and is part of the calibration certificate. If the coupling attenuation is supposed to be calibrated in the real emission measurement setup a serial resistance of 100 ? is needed to adapt the 150 ? of the CDNE to the 50°? measurement system. For this purpose we offer the optionally available adapter SR100-6W.

There is a resistive attenuator built in the BNC output to force a match. According to the standard CISPR/A/944/CD Fig. J2 a value bigger than 6 dB is demanded. By design the internal circuit has an attenuation of 9.5 dB. Together with the built in attenuator of 10.5 dB this results in a total attenuation of 20 dB. Thus the measurement port matches the 50 ? very well and supersedes an external attenuator.

The dual pole side of CA CDNE M2 (part A & B) has to be connected to the EuT port of the CDNE. The single pole 4 mm jack can be plugged into the EuT port of the SR100-6W. Due to the length of the CA CDN M2 part B the distance between the CDNE M2 and the SR100-6W is automatically set to 30 mm as described in the standard.

For the emission measurement acc. CISPR 15 the adapters are not required as data for the voltage division factor (correction) is automatically delivered. The adapters however are recommendable for a quick performance check or a calibration of the CDNE.