EM Test AMP 200N Low Frequency Signal Source DC (0Hz) to 250kHz

EM Test AMP 200N Low Frequency Signal Source DC (0Hz) to 250kHz

Weight:
Approx. 18kg
Amplifiers:
low-frequency signal source with amplifier
Dimensions:
19", 3HU (500mm x 449mm x 133mm)
Frequency range:
DC - 250kHz
General Data:
Technical Details
Harmonic Distortion (THD):
less than 0.1%
Operating Temperature:
10°C - 40°C
Output current:
Max. 5Arms up to 200kHz Max. 4Arms 200kHz - 250kHz
Output Impedance:
30 mOhm @ 1 kHz
Output voltage:
50Vrms, max. 140V(p-p) up to 100kHz 30Vrms 100kHz - 250kHz
Protection:
- Short circuit - Overtemperature
Signal power:
250W (nominal)
Supply Voltage:
115 V +10/-02%, 50/60 Hz or 230 V +10/-15%, 50/60 Hz
Manufacturer:
EM Test
Online Orders Ship Same Day

 

SKU:
sku-480

 

This product is available for shipping to North America and Western European countries.

Getting Started...

Check out our Google Reviews

Overview

EM Test AMP 200N Application:

AMP 200N - Low-frequency signal source for supply simulation and magnetic field testing

The AMP 200N has been designed as a low-frequency signal source to generate sinusoidal signals used to simulate ripple noise and ground shift noise as required by a variety of standards in the automotive industry e.g. as per Ford EMC-CS-2009.1, CI 210 and CI 250 as well as RI 150. The AMP 200N is controlled by the EM TEST Autowave to also allow the generation of non-sinusoidal and customised signals. Additionally, the AMP 200N can be used to generate magnetic fields by means of a radiation loop or small Helmholtz coils as per RI 140 of Ford EMC-CS-2009.1.

Standards

  • Chrysler CS-11809 (2009)
  • Chrysler CS-11979
  • Chrysler DC-11224 Rev.A
  • DaimlerChrysler DC-10615
  • DaimlerChrysler DC-11224
  • Ford EMC-CS-2009.1
  • GMW 3172
  • Jaguar JLR-EMC-CS V1.0 Amd 4
  • MAN 3285
  • SAE J1113-2
  • Tata TST/TS/WI/257

Benefits

AMP 200N - Signal generator/amplifier solution for ripple noise and magnetic field testing

The AMP 200N unifies a low-frequency signal generator and a powerful amplifier module giving a maximum amplitude of 150V peak-to-peak as required e.g. by Ford EMC-CS-2009.1. It generates both sinusoidal and transient signals. Equipped with a DDS it generates any sinusoidal signal with a frequency up to 250kHz. The AMP 200N is controlled by the EM TEST AutoWave in order to generate any sinusoidal or non-sinusoidal/transient signals and is therefore fully supported by the autowave.control software with its exhaustive library of pre-programmed standards and its outstanding reporting and documentation capabilities.

The AMP 200N can also be used for magnetic field testing using a Radiation Loop and Loop Sensor. Extended by the optional measuring module the AMP 200N offers means for frequency-selective current measurement, voltage measurement and measurement of the magnetic field strength.
Optional Product:
EM Test AMP 200N1.1 - High frequency option up to 500 kHz

Key Considerations

Manufacturer:
EM Test
Weight:
Approx. 18kg
Amplifiers:
low-frequency signal source with amplifier
Dimensions:
19", 3HU (500mm x 449mm x 133mm)
Frequency range:
DC - 250kHz
General Data:
Technical Details
Harmonic Distortion (THD):
less than 0.1%
Operating Temperature:
10°C - 40°C
Output current:
Max. 5Arms up to 200kHz Max. 4Arms 200kHz - 250kHz
Output Impedance:
30 mOhm @ 1 kHz
Output voltage:
50Vrms, max. 140V(p-p) up to 100kHz 30Vrms 100kHz - 250kHz
Protection:
- Short circuit - Overtemperature
Signal power:
250W (nominal)
Supply Voltage:
115 V +10/-02%, 50/60 Hz or 230 V +10/-15%, 50/60 Hz

Related EMC Equipment & Solutions

EM Test VDS 200N30 Voltage Drop Simulator

EM Test VDS 200N Series Automotive Voltage Drop Simulators

SKU: 1844-1

Applications: EMC Testing on EV Electric Vehicles Batteries & Charging Stations, Automotive Electrical Disturbances
Standards Met: ISO 7637 , FMC1278, & More
Max EUT DC Voltage (W/ Built In CDN): 60 Volts
Max EUT DC Current (W/ Built In CDN): up 200 Amps
$1,975.00
In Stock
Ordering Options
EM Test LD 200N Load Dump Generator for ISO 16750-2

EM Test LD 200N Load Dump Generator for ISO 16750-2

SKU: sku-817

Output: +/- output Safety laboratory connectors Coupling To the battery +lineDecoupling Via diodeDUT supply Max. 80V/30A
Freestyle Mode Micropulses: Rise time 1us 10us - 90us with 10us steps 100us - 900us with 100us steps 1ms - 10ms with 1ms steps Pulse duration 10ms - 1,200ms Int. resistor 0.5ohm - 38ohm, in steps of 0.1ohm
Test Standards: ISO 7637-2 Pulse 5b for 12V and 24V, ISO/WD 16750 Pulse 5b, and much more
Test Routines: Quick Start, User Defines Routines, Standards Test Routines Service
$2,290.00
Typically In Stock
Ordering Options
EM Test PFS 200N Power Fail Simulator for Automotive and EV Electronic Components

EM Test PFS 200N Power Fail Simulator for Automotive and EV Electronic Components

SKU: sku-1186

Applications: Automotive Power Fail Simulator For Voltage Dips and Interruptions
Standards Met: ISO 16750-2
OEM Standards Met: BMW GS 95003-2, Fiat 9.90110, Ford EMC-CS-2009.1, GMW 3172, Hyundai Kia ES, IVECO 16-2103, Mack Trucks 606GS15, Mitsubishi ES-X82010, PSA B21 7110, Volvo STD 515-003, Ford FMC 1278, BMW GS 95024-2-2, Jaguar JLR-EMC-CS, Tesla TS-0000425-05
Max EUT DC Voltage (W/ Built In CDN): 80 Volts
Max EUT DC Current (W/ Built In CDN): 30 Amps
Peak Inrush Current Capability: 70 Amps
IN STOCK
View Product Cart
EM Test UCS 500N5 Multifunctional Generator for EFT/Burst, Surge & Power Fail

EM Test UCS 500N5 Multifunctional Generator for EFT/Burst, Surge & Power Fail

SKU: 10240

Test Capabilities: Combination Wave Surge Immunity , EFT/Burst, Dips Interrupts & Variations
EMC Standards: IEC/EN 61000-4-4, IEC/EN 61000-4-5, IEC/EN 61000-4-11, IEC/EN 61000-4-29
Applications: CE Marking, Medical Devices, Industrial Machinery, Electronics & IT
Max EUT AC Voltage (w/ Built in CDN): 264 Volts
Max EUT AC Current (w/ Built in CDN): 16 Amps
Max EUT DC Voltage (w/ Built in CDN): 220 Volts
Max EUT DC Current (w/ Built in CDN): 10 Amps
Peak inrush current capability: 500 A (at 230 V)
EFT/Burst Pulse Output Capability: ±200 V to 4.8 kV (in 1 V steps) - open circuit±100 V to 2.4 kV ±100 A to 2.2 kA
Combination/Wave Surge Output Capability: ±200 V to 4.4 kV (in 1 V steps)
External Coupling: Data Lines (EFT & Surge), 3PH EUT
Weight: 25 kg's (55 Lbs)
Dimensions: 19", 3HU
Standards Met: FCC 97-270 (part 68); IEC 60255-22-5; IEC 61000-4-11; IEC 61000-4-29; IEC 61000-4-4; IEC 61000-4-5; IEC 61000-4-8; IEC 61000-4-9; IEC 61326; IEC 61850-3
Inquire for Availability
View Product Cart

Connect with The EMC Shop

Our experienced staff can help you with applications, purchase and rental options.

Contact Form