Teseq CDN M1-10 Coupling Network 10 KHz to 80 MHz for PE Lines

Teseq CDN M1-10 Coupling Network 10 KHz to 80 MHz for PE Lines

Weight:
3.3 Lbs (1.5 kg)
Application/Test Type:
switchable 2 or 3 power lines, (L+N or L+N+PE)
Common Mode Impedance:
10 kHz to 26 MHz: 150 Ω ±20 Ω; 26 MHz to 80 MHz: 150 Ω +60 Ω / -45 Ω
Current Rating:
Current max. (no saturation): 300 mA; Current max. (1 s for PE line test): 25 A
Dimensions:
3.9" x 3.9" x 9.5" (100 mm x 100 mm x 240 mm)
Frequency Range:
150 kHz to 230 MHz
Insertion Loss:
Less than 0.1 dB
RF Connector:
BNC 50 Ω
RF Input Voltage:
Less than 20 Volts
Standards Met:
IEC/EN 61000-4-6
Voltage Division Factor:
10 dB ±1 dB
Voltage Rating:
3 kV DC, 2 sec
Manufacturer:
Teseq
Online Orders Ship Same Day
$790.00

 

SKU:
sku-222
Getting Started...

Overview

IEC/EN 61000-4-6 specifies the design and performance of a range of coupling/decoupling networks (CDNs). Each CDN is specific to the type of cable and the intended signal carried on the cable. Teseq offers an extensive range of CDNs which fully comply with the requirements of the standard and provide a simple and reliable method of injecting RF energy into the equipment under test (EUT).

Whilst the published standard only specifies the performance of CDN from 150 kHz to 80 MHz, most of Teseq CDNs are specially designed to give the same performance to a wider frequency range. This is required by some product specific standards. Each CDN is also useable for emission testing. Special types meet the requirements of CISPR 15 or can be used as impedance stabilization network (ISN) defined in CISPR 22.

Teseq CDN M1-10 Features:

  • Coupling/Decoupling Network (CDN) CDN M Type
  • Designed for IEC/EN 61000-4-6
  • Types with 4 mm banana sockets
  • Performance 10 KHz to 80 MHz for PE Lines
  • Current: 200 mA (25 Amp for 1 seconf PE line Test)
  • Common Mode Impedance: 150 Ohms
  • Insertion loss: less than 0.1 dB

Key Considerations

Manufacturer:
Teseq
Weight:
3.3 Lbs (1.5 kg)
Application/Test Type:
switchable 2 or 3 power lines, (L+N or L+N+PE)
Common Mode Impedance:
10 kHz to 26 MHz: 150 Ω ±20 Ω; 26 MHz to 80 MHz: 150 Ω +60 Ω / -45 Ω
Current Rating:
Current max. (no saturation): 300 mA; Current max. (1 s for PE line test): 25 A
Dimensions:
3.9" x 3.9" x 9.5" (100 mm x 100 mm x 240 mm)
Frequency Range:
150 kHz to 230 MHz
Insertion Loss:
Less than 0.1 dB
RF Connector:
BNC 50 Ω
RF Input Voltage:
Less than 20 Volts
Standards Met:
IEC/EN 61000-4-6
Voltage Division Factor:
10 dB ±1 dB
Voltage Rating:
3 kV DC, 2 sec

Related EMC Equipment & Solutions

Teseq CDN M416 4-Line Coupling/Decoupling Network

Teseq CDN M416 4-Line Coupling/Decoupling Network

SKU: sku-225

Weight: 700 grams (1.5 LB.'s)
Application/Test Type: 3 power lines, (L+N+PE), (2L+PE), (Optional L+L+L)
Common Mode Impedance: 150 Ω +10/-20 Ω
Current Rating: 10 Amps Maximum
Decoupling of Common Mode Disturbance: Greater than 30 dB
Dimensions: 4.1 x 3 x 5 inches (10.5 x 7.5 x 12.5 cm)
Frequency Range: 150 kHz to 230 MHz (Optional 10 kHz - 80 MHz)
Insertion Loss: Greater than 0.1 dB
Mains & EUT Connections: 4 mm, safety (Optional IEC 320 16A)
RF Connector: BNC, 50 Ω
RF Input Voltage: Less than 30 V
Standards Met: IEC 61000-4-6, CISPR 16-1-2, CISPR 16-2-1 and CISPR 15
Voltage Division Factor: 20 dB ±1.5 dB
Voltage Rating: AC max. voltage (line to ground) / (line to line): 250 V / 433 V (CDN M216-1000V: 500 V / 1000 V); DC max. voltage (line to ground) / (line to line): 400 V / 800 V (CDN M216-1000V: 1000 V / 2000 V); Test voltage: 3 kV DC, 2 sec
View Product View Product
Teseq CDN ST08 Coupling Decoupling Network - The EMC Shop

Teseq CDN ST08 Coupling Decoupling Network

SKU: 8413

Frequency Range: 10 kHz to 80 MHz
Application: CDN for screened eight lines with RJ45 connector
Current Rating: 1000 mA
EUT Connector: BNC 50 Ω
Common mode impedance (EUT Port) 10 kHz to 26 MHz: 150 Ω ±20 Ω
Common mode impedance (EUT Port) 26 MHz to 80 MHz: 150 Ω +60 Ω /-45 Ω
RF Voltage: <20 V
$1,600.00
Typically in Stock
Teseq CDN 117 2-Wire Data Line Coupling Network

Teseq CDN 117 2-Wire Data Line Coupling Network

SKU: sku-108

Weight: 2.1 kg (4.6 lbs)
Application/Test Type: 1.2 / 50 μs pulse up to 6.6 kV
Coupling: INA 170: spark gap device, 90 V trip voltage; INA 174A: capacitor 0.5 μF
Current Rating: 1.5 Amps
Decoupling chokes 1 kHz: 20 mH nominal
Dimensions: 300 mm x 55 mm x 80 mm
Ohmic resistance per path: Less than 2.5 Ω
RF Connector: 4 mm safety banana; Fischer 103
Series resistor: 2 x 40 Ω, 6 W
Transmission 3 dB BW: 800 Hz
Voltage Rating: 250 Volts AC/DC
$3,080.00
Ordering Options
Teseq CDN M316 Coupling/Decoupling Network (CDN) CDN M3 Type

Teseq CDN M316 Coupling/Decoupling Network (CDN) CDN M3 Type

SKU: sku-224

Weight: 700 grams (1.5 LB.'s)
Application/Test Type: 3 power lines, (L+N+PE), (2L+PE), (Optional L+L+L)
Common Mode Impedance: 150 Ω +10/-20 Ω
Current Rating: 10 Amps Maximum
Decoupling of Common Mode Disturbance: Greater than 30 dB
Dimensions: 4.1 x 3 x 5 inches (10.5 x 7.5 x 12.5 cm)
Frequency Range: 150 kHz to 230 MHz (Optional 10 kHz - 80 MHz)
Insertion Loss: Greater than 0.1 dB
Mains & EUT Connections: 4 mm, safety (Optional IEC 320 16A)
RF Connector: BNC, 50 Ω
RF Input Voltage: Less than 30 V
Standards Met: IEC 61000-4-6, CISPR 16-1-2, CISPR 16-2-1 and CISPR 15
Voltage Division Factor: 20 dB ±1.5 dB
Voltage Rating: AC max. voltage (line to ground) / (line to line): 250 V / 433 V (CDN M216-1000V: 500 V / 1000 V); DC max. voltage (line to ground) / (line to line): 400 V / 800 V (CDN M216-1000V: 1000 V / 2000 V); Test voltage: 3 kV DC, 2 sec
View Product Cart
Com-Power CDN-M350E 150 kHz to 230 MHz Coupling Decoupling Network

Com-Power CDN-M350E 150 kHz to 230 MHz Coupling Decoupling Network

SKU: sku-858

Weight: 5 lbs. 2.3 kg
Application/Test Type: Three conductor power cable
Common Mode Impedance: 150 kHz - 26 MHz: 150Ω ± 20Ω 26 MHz - 80 MHz: 150Ω + 60Ω / – 45Ω 80 MHz - 230 MHz: 150Ω + 60Ω / – 60Ω
Current Rating: 25 Amps AC / 17 Amps DC (Max)
Decoupling of Common Mode Disturbance: ≥ 40dB (EUT/AE)
Dimensions: 6 x 6 x 13 inches 15.2 x 15.2 x 33 cm
Frequency Range: 150 kHz to 230 MHz
Mains & EUT Connections: 4 mm shrouded banana sockets
RF Connector: 50 Ω BNC (Female)
RF Input Voltage: 40 V (Max)
Standards Met: IEC / EN 61000-4-6
Voltage Division Factor: 9.5 dB +4 / -1
Voltage Rating: 250 V AC / 350 V DC (Line to Ground)
View Product Cart

Connect with The EMC Shop

Our experienced staff can help you with applications, purchase and rental options.

Contact Form